Exfo CableSHARK P3 VF/DSL Cable Qualifier Manuel d'utilisateur Page 135
- Page / 321
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CableSHARK P3 User Guide
123
SAVE TO USB
Choosing SAVE TO USB from the SAVE / UPLOAD pop-up menu invokes
the SAVE SESSION menu. From here, the test results can be saved to
external USB memory. See Section 5.3 for more information.
The remainder of the buttons are as follows:
ZOOM IN VERT /
ZOOM OUT VERT
Use these function buttons to zoom in and out based on the vertical level
scale. Please note after the completion of a test, the ZOOM OUT VERT option
will be disabled as it is impossible to ZOOM OUT. Press the ZOOM IN VERT
button once or multiple times and the ZOOM OUT VERT button will appear.
Likewise, when the maximum zoom level is achieved, the ZOOM IN VERT
button will disappear.
ZOOM IN HORIZ /
ZOOM OUT HORIZ
Use these function buttons to zoom in and out based on the horizontal graph
scale. Please note after the completion of a test, the ZOOM OUT HORIZ
option will be disabled as it is impossible to ZOOM OUT. Press the ZOOM IN
HORIZ button once or multiple times and the ZOOM OUT HORIZ button will
appear. Likewise, when the maximum zoom level is achieved, the ZOOM IN
HORIZ button will disappear.
TEST SETUP
Pressing the function button associated with TEST SETUP activates the
Longitudinal Balance Test Setup menu. Test parameters can be modified and
the test can be run once again from this screen.
MAIN MENU
Select MAIN MENU to return to the Main Menu.
- CableSHARK P3 3
- VF / DSL Cable Qualifier 10
- Patent Information 11
- 1.2 Unpacking the CableSHARK 13
- 1000 ft (300 m) 22
- 4.1.1 The Front Panel 27
- 4.1.2 The Rear Panel 29
- 4.2 Powering the CableSHARK 33
- 5.1.1 Self Tests 37
- 5.2.2 Single-Ended Testing 39
- 5.2.3 End-to-End Testing 40
- 5.3.1 Saving Results 41
- 5.3.2 Recalling Results 43
- 5.4 Reference Masks 45
- 5.6 Bandwidth Requirements 50
- Section 6 Main Menu 51
- 6.2 Responder Mode 58
- 6.3 Recall Results 59
- 6.4 The System Setup Menu 59
- 7.2.1 Automatic TDR Test 65
- 7.2.2 Manual TDR Test 66
- 7.3 Frequency Response Tests 67
- 7.4.2 End-to-End DMT Test 69
- 7.5 Noise Tests 70
- 7.7 Load Coil Detection Test 71
- 7.8 Spectral Detective 72
- 7.10 Return Loss 73
- 7.12 4 Wire Xtalk 73
- 7.14 ADSL Auto Test 74
- 7.15 SHDSL Auto Test 75
- 7.16 VF Auto Test 76
- 7.17 Ground Resistance Test 77
- 7.19 K-Test 78
- 7.20 Ringer Detection 79
- 7.21 VF Tests 79
- 7.22 LoopMapper™ Tests 79
- CableSHARK 81
- FREQUENCY RESPONSE TEST SETUP 84
- 8.2.1 Setting up a TDR Test 89
- 8.2.2 Manual TDR Testing 95
- 8.2.3 Auto TDR Testing 101
- 8.2.4 TDR Application Hints 102
- CableSHARK P3 User Guide 103
- 8.3.1 Setting up a DMT Test 105
- DMT BITS PER 107
- (m/μS): 108
- 8.3.2 Running an ADSL Test 110
- DMT TEST RESULT 114
- 8.4..Noise Measurements 118
- 8.4.2 Running a Noise Test 124
- 00:00:00 125
- TO MEM 130
- TO USB 135
- 8.7.1 Setting up a DMM Test 142
- 8.7.2 Running a DMM Test 148
- 8.8.. 4-Wire Crosstalk Test 151
- 17.3 kHz to 2.208 MHz) 155
- > 100 M 157
- 8.10 LoopMapper™ 159
- 8.10.2 LoopMapper Testing 161
- 8.11.1 Auto Test Setup 168
- IGURE 8.11.1.3C – PHONE BOOK 174
- Central Office 185
- Customer 185
- IGURE 9.2D – ADSL AT CO SIDE 191
- 11.1..Running a SHDSL Test 199
- IGURE 12.1C – BATTERY CROSS 201
- IGURE 12.1.1.3A – RFL CABLE 203
- Black Red Green 204
- Yel low Blue Green 204
- Black Red Gnd 208
- 12.2 Running a RFL Test 210
- 12.3 RFL Hints 212
- + [ 0.0022 * ( T 213
- - 68°F ) * R 213
- - 20°C ) * 0.00393 * R 214
- Line card = not detected 222
- 15.1.3 Sending 3 Tone Slope 233
- 15.2.3 RX 3 Tone Slope 240
- 15.3 Noise Test 243
- 15.4 Impulse Noise Test 245
- 00:09:12 246
- 15.5 Power Influence 247
- SAVE/UPLOAD button 248
- 16.2 Setting up a K-test 249
- 16.3 Running the K-test 250
- 16.3.3 Running a Test 256
- A.1 Loop Topologies 259
- A.2 Attenuation Responses 261
- Transmitter Characteristics 272
- Transmitter Functions 272
- ± 50 ppm 275
- ± 1.0 dB typical 275
- ± 0.5 dB 277
- SHDSL Data Rate Test 278
- PSD Noise Measurement 278
- Longitudinal Balance Test 279
- DMM (Digital Multimeter) 279
- Isolation resistance 280
- Spectral Detective 280
- 4-Wire Crosstalk 280
- Visi-SHARK 282
- Appendix D Safety 283
- Appendix E Warranty 287
- Certification 288
- F.1 Software Policy 289
- F.2 Upgrading Software 289
- J.1 Installing the Software 295
- J.3.1 Running Visi-SHARK 296
- IGURE J.4.2B – SOCKET ERROR 301
- J.6.1 File Menu 305
- J.6.2 Screen Image menu 307
- J.6.3 New Connection Menu 310
- J.6.4 View Menu 311
- J.6.5 Window Menu 311
- Telecom Test and Measurement 321
Produits connexes et manuels pour Instruments de mesure Exfo CableSHARK P3 VF/DSL Cable Qualifier
Instruments de mesure Exfo FIP-400 Fiber Inspection Probe and ConnectorMax Manuel d'utilisateur
(78 pages)
(78 pages)
Instruments de mesure Exfo FIP-400B Fiber Inspection Probe Multifiber Manuel d'utilisateur
(2 pages)
(2 pages)
Instruments de mesure Exfo FIP-400B Fiber Inspection Probe Multifiber Manuel d'utilisateur
(2 pages)
(2 pages)
Instruments de mesure Exfo FIP-400B Fiber Inspection Probe Multifiber Manuel d'utilisateur
(2 pages)
(2 pages)
Instruments de mesure Exfo FIP-400B Fiber Inspection Probe Multifiber Manuel d'utilisateur
(2 pages)
(2 pages)
Instruments de mesure Exfo FIP-400B Fiber Inspection Probe and ConnectorMax2 Manuel d'utilisateur
(111 pages)
(111 pages)
Instruments de mesure Exfo FIP-400B Fiber Inspection Probe and ConnectorMax2 Manuel d'utilisateur
(103 pages)
(103 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels