Exfo BV10 Performance Endpoint Unit Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Instruments de mesure Exfo BV10 Performance Endpoint Unit. EXFO BV10 Performance Endpoint Unit User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 18
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Installation Guide
Performance Endpoint Unit
BV10
Vue de la page 0
1 2 3 4 5 6 ... 17 18

Résumé du contenu

Page 1 - Performance Endpoint Unit

Installation GuidePerformance Endpoint UnitBV10

Page 2

Getting Started6 BV10Connecting the Power3. Connect the other end of the wires to the DC power source.4. To add a redundant DC power source on the BV1

Page 3 - Certification Information

BV10-100 and BV10-1000 72 Physical Interfaces, LEDs, and ButtonsThis section describes all connectors (ports), LEDs, and buttons available on the BV10

Page 4 - Installation Instructions

Physical Interfaces, LEDs, and Buttons8 BV10Port Availability on BV10Port Availability on BV10 Connecting the TEST Port Interface The BV10-100 provide

Page 5 - 1 Getting Started

Physical Interfaces, LEDs, and ButtonsBV10-100 and BV10-1000 9Connecting the TEST Port InterfaceSFP Port (BV10-1000)The BV10-1000 provides an optional

Page 6

Physical Interfaces, LEDs, and Buttons10 BV10Connecting the Management InterfacesConnecting the Management InterfacesThe management interface can be c

Page 7 - Grounding the BV10

Physical Interfaces, LEDs, and ButtonsBV10-100 and BV10-1000 11Connecting the Management InterfacesCONSOLE PortConnecting a PC to the CONSOLE port pro

Page 8

Physical Interfaces, LEDs, and Buttons12 BV10LEDsLEDs POWER  On (Green) indicates that the BV10 unit is receiving power from an external source. Off

Page 9

Physical Interfaces, LEDs, and ButtonsBV10-100 and BV10-1000 13RESET and DEFAULT ButtonsRESET and DEFAULT Buttons The RESET and DEFAULT buttons are re

Page 10 - Connecting the Power

www.EXFO.com · [email protected]/N: 1065620CORPORATE HEADQUARTERS 400 Godin Avenue Quebec (Quebec) G1M 2K2 CANADATel.: 1 418 683-0211 · Fax: 1 418 683-

Page 11 - BV10 Models

ii BV10Copyright © 2010–2014 EXFO Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted

Page 12 - Port Availability on BV10

Certification InformationBV10-100 and BV10-1000 iiiCertification InformationNorth America Regulatory StatementThis unit was certified by an agency app

Page 13 - SFP Port (BV10-1000)

iv BV10Installation InstructionsInstallation InstructionsThis document describes the basic steps for installing the BV10. Refer to the BV10 user guide

Page 14 - LAN Port

BV10-100 and BV10-1000 11 Getting Started Installing the BV10 in a Rack The BV10 can be mounted in a rack using the rack mount accessory kit (ordered

Page 15 - CONSOLE Port

Getting Started2 BV10Connecting the PowerConnecting the Power The BV10 is available with either an AC power supply, DC +24 V connector, or DC –48 V co

Page 16

Getting StartedBV10-100 and BV10-1000 3Connecting the PowerGrounding the BV10The BV10 is equipped with a ground lug and hardware attached to the back

Page 17 - RESET and DEFAULT Buttons

Getting Started4 BV10Connecting the PowerConnecting the BV10 using an AC/DC Power SourceThe typical output voltage of the external brick AC power supp

Page 18

Getting StartedBV10-100 and BV10-1000 5Connecting the PowerThe following figures show the –48 V and +24 V DC units.--2. Connect the plug to one of the

Commentaires sur ces manuels

Pas de commentaire