Exfo FLS-2600B Tunable Laser Source Manuel d'utilisateur Page 39
- Page / 157
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Setting Sweep Parameters
Tunable Laser Source 31
Setting the Sweep Step
Setting the Sweep Step
You can set the size of the step (in nm or THz) for your step-by-step sweep.
Your tunable laser source unit was designed to give a constant step value
using nm as units. When steps are given in THz, the selected step value
represents the average value of the steps during the sweep, since an
interval in nm does not always have the save equivalent value in THz
according to the wavelength bandwidth you have selected.
To set the step:
1. Make sure you have selected the step-by-step sweeping mode (as seen
in Selecting the Sweep Mode on page 30).
2. Press Sweep.
3. Turn the selection dial clockwise until STEP is displayed.
4. Press ENTER. The Edit marker starts blinking in the lower part of the
display.
5. Turn the selection dial clockwise or counterclockwise to select the
desired size for the step.
Edit
nm
- FLS-2600B 1
- Contents 3
- Manufacturer 7
- DECLARATION OF CONFORMITY 7
- 1 Introducing the FLS-2600B 9
- 2 FLS-2600B 10
- General Information 10
- RS-232 Connector Pinout 11
- Typical Applications 12
- IMPORTANT 13
- 2 Safety Information 15
- Electrical Safety Information 16
- Power Cable 17
- 3 Getting Started with Your 19
- Tunable Laser Source 19
- Tunable Laser Source 13 21
- 4 Setting Standard Parameters 23
- Turning the Sound On or Off 24
- Switching between Normal and 25
- High-Resolution (HR) Modes 25
- Selecting the Display Unit 26
- Selecting a Wavelength 27
- 20 FLS-2600B 28
- Setting the Power 29
- Adding Items to Lists 30
- Deleting Items from Lists 31
- Tunable Laser Source 25 33
- 26 FLS-2600B 34
- Reverting to Factory Settings 35
- 5 Setting Sweep Parameters 37
- Selecting the Sweep Mode 38
- Setting the Sweep Step 39
- Setting the Pauses 40
- Setting the Sweep Speed 41
- 34 FLS-2600B 42
- Tunable Laser Source 35 43
- Setting the Cycle Options 44
- Setting the Sweep Direction 45
- 40 FLS-2600B 48
- Starting a Sweep 51
- 7 Maintenance 53
- Use only with a 250V fuse 58
- Employer uniquement avec 58
- Software Upgrades 61
- 54 FLS-2600B 62
- Recalibrating the Unit 64
- Recycling and Disposal 64
- 8 Troubleshooting 65
- FLS-2600B-XX-XX 66
- Transportation 67
- 9 Warranty 69
- Liability 70
- Service and Repairs 72
- Tunable Laser Source 65 73
- A Technical Specifications 75
- Technical Specifications 76
- B Trigger Option Theory 77
- 70 FLS-2600B 78
- C Remote Control 79
- 72 FLS-2600B 80
- Tunable Laser Source 73 81
- 74 FLS-2600B 82
- Communication Parameters 83
- 76 FLS-2600B 84
- Bits Mnemonics Bit Value 84
- Tunable Laser Source 77 85
- 78 FLS-2600B 86
- Remote Control 87
- SCPI Commands 88
- General Commands 90
- 84 FLS-2600B 92
- 86 FLS-2600B 94
- Tunable Laser Source 87 95
- 88 FLS-2600B 96
- Tunable Laser Source 89 97
- Specific Commands 98
- DISPlay:DIMMer 99
- DISPlay:DIMMer? 99
- OUTPut:ASE? 100
- OUTPut:MODE 100
- OUTPut:MODE? 101
- OUTPut:STATe 101
- OUTPut:STATe? 102
- SOURce:MODE 102
- SOURce:MODE? 103
- SOURce:POWer:ALC 103
- SOURce:POWer:ALC? 104
- SOURce:POWer:LIMit:HIGH? 104
- SOURce:POWer:LIMit:LOW? 104
- SOURce:POWer:LIMit:STEP? 105
- SOURce:SWEep:MODE 105
- SOURce:SWEep:MODE? 106
- SOURce:SWEep:CENTer? 106
- SOURce:SWEep:COUNt 107
- SOURce:SWEep:COUNt? 107
- SOURce:SWEep:REPeat 108
- SOURce:SWEep:REPeat? 108
- SOURce:SWEep:REVerse 109
- SOURce:SWEep:REVerse? 109
- SOURce:SWEep:STARt:WAVelength 110
- SOURce:SWEep:STOP:WAVelength 111
- SOURce:SWEep:STOP:WAVelength? 111
- SOURce:SWEep:SPAN? 112
- SOURce:SWEep:SPEed 112
- SOURce:SWEep:SPEed? 113
- SOURce:SWEep:SPEed:LIMit:LOW? 114
- SOURce:SWEep:STATe 114
- SOURce:SWEep:STATe? 115
- SOURce:SWEep:DURation? 115
- SOURce:SWEep:STEP 116
- SOURce:SWEep:STEP? 116
- SOURce:SWEep:STEP:LIMit:HIGH? 117
- SOURce:SWEep:STEP:LIMit:LOW? 117
- SOURce:SWEep:PAUSe 118
- SOURce:SWEep:PAUSe? 118
- SOURce:SWEep:PAUSe:LIMit:LOW? 119
- SOURce:SWEep:TRIGger 120
- SOURce:SWEep:TRIGger? 120
- SOURce:WAVelength 121
- SOURce:WAVelength? 121
- SOURce:WAVelength:LIMit:HIGH? 122
- SOURce:WAVelength:LIMit:LOW? 122
- SOURce:WAVelength:LIMit:STEP? 123
- SYSTem:ERRor? 123
- SYSTem:VERSion? 124
- UNIT:WAVelength 124
- UNIT:WAVelength? 125
- Programming Commands 126
- 120 FLS-2600B 128
- SOURce:SWEep:STEPped:PROGram 130
- SOURce:SWEep:STEPped:PROGram? 132
- Other Commands 134
- SOURce:SWEep:RECAll? 135
- Quick Reference Command Tree 136
- Tunable Laser Source 129 137
- Tunable Laser Source 131 139
- Tunable Laser Source 133 141
- Error Messages 142
- Description Probable Cause 143
- 136 FLS-2600B 144
- Tunable Laser Source 137 145
- Tunable Laser Source 139 147
- GPIB Troubleshooting 149
- Tunable Laser Source 143 151
- Tunable Laser Source 145 153
- ₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩ 155
- MARKING REQUIREMENTS 156
Produits connexes et manuels pour Instruments de mesure Exfo FLS-2600B Tunable Laser Source
(215 pages)
Instruments de mesure Exfo IQS-12004B DWDM Passive Component Test System for Manuel d'utilisateur
(437 pages)
(437 pages)
Instruments de mesure Exfo IQS-1600 High-Speed Power Meter for IQS-500/600 Manuel d'utilisateur
(238 pages)
(238 pages)
Instruments de mesure Exfo IQS-1700 High Performance Power Meter for IQS-500/ Manuel d'utilisateur
(204 pages)
(204 pages)
Instruments de mesure Exfo IQS-2400 WDM Laser Source for IQS-500/600 Manuel d'utilisateur
(194 pages)
(194 pages)
Instruments de mesure Exfo IQS-2600B Tunable Laser Source for IQS Platforms Manuel d'utilisateur
(142 pages)
(142 pages)
Instruments de mesure Exfo IQS-3150 Variable Attenuator for IQS-500/600 Manuel d'utilisateur
(161 pages)
(161 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels