Exfo FTB-800 Series for FTB-1 Manuel d'utilisateur Page 125
- Page / 621
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Test Setup - Test Configurator, Timer, and System
NetBlazer 115
EtherBERT and Unframed BERT
Bit/Pattern Error
The configuration of Bit Error is available with all patterns at the exception
of Seed A and Seed B for which Pattern Error is available.
Pass/Fail Verdict allows to enable and configure bit/pattern error
rate/count threshold prior to run the test. This allows for a simple
pass/fail verdict, leaving no room for misinterpretation of the test
results. To enable the pass/fail verdict, select either
Bit/Pattern Error Count or Bit/Pattern Error Rate (default is
Disabled).
BER Threshold allows to enter the threshold Count or Rate value that
will be used to declare the pass/fail verdict.
For Count, enter the maximum bit/pattern error count allowed before
declaring a fail verdict: 0 (default) to 999999.
For Rate, enter the maximum bit/pattern error rate allowed before
declaring a fail verdict: 1.0E-14 to 1.9E-01. The default value is 1.0E-12.
- FTB-700G/800 Series 1
- Certification Information 3
- Contents 5
- NetBlazer vii 7
- NetBlazer ix 9
- Multiservice Tester 11
- IMPORTANT 12
- 2 Safety Information 13
- 4 FTB-700G/800 Series 14
- 6 FTB-700G/800 Series 16
- 3 Getting Started 17
- FTB-810 and FTB-810G Modules 19
- Physical Interfaces and LEDs 20
- FTB-860G Module 21
- FTB-860GL Module 21
- FTB-870, FTB-720G 22
- , and FTB-730G 22
- Modules 22
- FTB-880 Module 23
- 14 FTB-700G/800 Series 24
- 100M-4.25G (PORT #1/#2) 26
- 8.5G-11.3G (PORT #1) 27
- 155M-2.5G (PORT #1) 28
- 10G (PORT #1) 29
- ETHERNET 10G (PORT #1) 30
- NetBlazer 21 31
- ETHERNET 10/100/1000M 32
- 2M-155M (PORT #1) 32
- 2M-52M (PORT #2) 32
- 1.5M/2M (PORT #1/#2) 32
- AUX Connection 33
- Fibre Cables Connection 33
- EXT CLK 34
- 5 Graphical User Interface 35
- Overview 35
- Status Bar 36
- NetBlazer 27 37
- Title Bar 38
- Global Indicator 39
- Global Verdict 40
- Global Alarm 41
- Test Control 42
- Test Menu 42
- Application Buttons 42
- Options Description 43
- 34 FTB-700G/800 Series 44
- Zoomed-In/Zoomed-Out Views 45
- Arrow Buttons 45
- Keyboard Usage 46
- 38 FTB-700G/800 Series 48
- ITU T.50 Characters 48
- OTN BERT 50
- Path/Mapping 51
- SONET/SDH BERT 52
- Path/Mapping 53
- For SDH BERT 54
- DSn/PDH BERT 55
- 46 FTB-700G/800 Series 56
- SONET/SDH - DSn/PDH BERT 57
- 48 FTB-700G/800 Series 58
- For SDH: 59
- NI/CSU Emulation 60
- ISDN PRI 61
- EtherSAM (Y.1564) 62
- RFC 2544 63
- EtherBERT 64
- Traffic Gen & Mon 65
- Third-Party Remote Loopback 67
- Through Mode 68
- Carrier Ethernet OAM 70
- FTB-700G/800 Series EEC 73
- FC BERT 74
- CPRI/OBSAI BERT 75
- Transport Test Applications 77
- 68 FTB-700G/800 Series 78
- 70 FTB-700G/800 Series 80
- Packet Sync Test Applications 81
- 72 FTB-700G/800 Series 82
- NetBlazer 73 83
- Timer, and System 87
- 78 FTB-700G/800 Series 88
- Block Subtab or Pop Up 88
- Test Application 88
- Timer, see page 234 90
- System, see page 231 90
- Test Configurator Overview 91
- Ethernet Test Applications: 92
- Wireless Test Application: 92
- NetBlazer 83 93
- NetBlazer 87 97
- NetBlazer 89 99
- 90 FTB-700G/800 Series 100
- Modify Structure Button 100
- Test Interface/Rate 100
- Interface/Rate Connector 101
- These patterns are 102
- Loopback Mode 103
- Signal Auto-Detect 105
- 1588 PTP 106
- NetBlazer 97 107
- PTSF Alarm Timeout/Threshold 109
- Quality Level 109
- Pass/Fail Verdict 110
- Restore 1588 PTP Defaults 110
- NetBlazer 101 111
- 102 FTB-700G/800 Series 112
- Bit Error 113
- Service Disruption 113
- 104 FTB-700G/800 Series 114
- Layer Signal Defect 114
- NetBlazer 105 115
- Multi-Pattern Configuration 116
- Cable Test 117
- SFP/SFP+ 119
- Clock Synchronization 120
- Ext Clock In 120
- NetBlazer 111 121
- Ext Clock Out 122
- NetBlazer 113 123
- EtherBERT and Unframed BERT 124
- Bit/Pattern Error 125
- Ethernet Frame 127
- EtherSAM - Burst 128
- Parameters 129
- EtherSAM - Global 130
- Subtests 131
- 122 FTB-700G/800 Series 132
- Global Options 133
- Restore EtherSAM Defaults 133
- EtherSAM - Ramp 134
- Delete Step 135
- Defaults 135
- Payload Type and Code 137
- Global (Fibre Channel) 140
- Round-Trip Latency 141
- Test Timer 142
- Interface (Ethernet) 143
- 134 FTB-700G/800 Series 144
- WIS Button 145
- Physical Interface 146
- TX Frequency 147
- RX Frequency 148
- World Wide Name (WWN) 149
- Buffer to Buffer Flow Control 150
- NetBlazer 141 151
- ISDN PRI - Call Management 153
- Answer Mode 155
- Call Control 156
- ISDN PRI - ISDN Settings 158
- Restore ISDN PRI Defaults 159
- MAC/IP/UDP 161
- Modify Frame Structure 162
- Preamble/SFD 163
- NetBlazer 159 169
- NetBlazer 161 171
- 162 FTB-700G/800 Series 172
- DSCP Codepoints: 172
- NetBlazer 163 173
- Network 174
- NetBlazer 165 175
- NetBlazer 167 177
- RFC 2544 - Global 179
- Subtests and Estimated Time 180
- Frame Distribution 180
- Restore RFC 2544 Defaults 181
- RFC 2544 - Subtests 182
- Back-to-Back 185
- Frame Loss Configuration 186
- Latency Configuration 187
- 178 FTB-700G/800 Series 188
- Thresholds Button 189
- 180 FTB-700G/800 Series 190
- S-OAM Mode 191
- S-OAM Responder 191
- Thresholds 192
- Local Parameters 193
- Peer MEP Parameters 193
- Continuity Check 194
- Test Function 194
- NetBlazer 185 195
- NetBlazer 187 197
- Services - Global 198
- SLA Button 199
- Total TX Rate 199
- Copy Service Button 200
- Services - Profile 201
- Profile 202
- 194 FTB-700G/800 Series 204
- Component Description 204
- Test Parameters 205
- SLA Parameters 206
- NetBlazer 197 207
- Signal (Transport) 208
- Signal LBO 209
- Signal Configuration 213
- Background 214
- Channel 215
- Modify DS0/E0 215
- 206 FTB-700G/800 Series 216
- NetBlazer 207 217
- Loopback button 218
- Modify Loop Codes button 219
- NetBlazer 211 221
- 212 FTB-700G/800 Series 222
- NetBlazer 213 223
- OC/STM Signal 224
- STS/AU and VT/TU Mappings 225
- 216 FTB-700G/800 Series 226
- NetBlazer 217 227
- Smart Loopback 228
- Streams - Global 230
- NetBlazer 221 231
- Streams - Profile 232
- NetBlazer 223 233
- Shaping 235
- QoS Metrics 237
- ESMC Monitoring 239
- ESMC Generation 240
- Restore SyncE Defaults 240
- Factory Default 241
- Remote Control 241
- TCP Throughput 242
- TCP Throughput Configuration 243
- 234 FTB-700G/800 Series 244
- NetBlazer 235 245
- Traces (OTN) 246
- NetBlazer 237 247
- 238 FTB-700G/800 Series 248
- Traces (SONET/SDH) 249
- TCM Access Point Identifier 250
- 9Test Results 251
- Test Results 252
- Ethernet Test Applications 252
- Wireless Test Application 253
- Alarms/Errors Overview 254
- Statistic Values 255
- Alarms/Errors 256
- NetBlazer 249 259
- 250 FTB-700G/800 Series 260
- LOC (Loss Of Clock) 260
- NetBlazer 251 261
- NetBlazer 253 263
- NetBlazer 255 265
- Ethernet 267
- NetBlazer 259 269
- Fibre Channel 270
- Interface 271
- IP/UDP/TCP 273
- NetBlazer 265 275
- ODUx-TCM 277
- CSF (Client Signal Fail) 279
- NetBlazer 271 281
- NetBlazer 277 287
- Section/Line / RS/MS 289
- STS-x/AU-x 291
- 284 FTB-700G/800 Series 294
- ESMC Loss 294
- TCM (SONET/SDH) 295
- NetBlazer 287 297
- NetBlazer 289 299
- NetBlazer 291 301
- NetBlazer 293 303
- 294 FTB-700G/800 Series 304
- Inject Button 305
- Inject button 307
- PT (Payload Type) 309
- Graph (RFC 2544) 310
- ISDN Logger 311
- NetBlazer 303 313
- NetBlazer 305 315
- Sort By 317
- Label 1 and Label 2 319
- Total TX/RX MPLS 319
- Performance Monitoring 320
- Near-End 321
- 312 FTB-700G/800 Series 322
- Signal SES Threshold 322
- NetBlazer 313 323
- Far-End 324
- PTP Stats 327
- 318 FTB-700G/800 Series 328
- Quality Level (1588 PTP) 329
- Quality Level (SyncE) 331
- NetBlazer 323 333
- Loopback 334
- Frame Delay 335
- Frame Loss 336
- Synthetic Loss 337
- Service Name and Selection 338
- Committed/Excess 338
- Committed/Excess Steps 339
- Service Performance 340
- RX Frame Count 341
- Streams - Jitter 342
- Streams - Latency 343
- Streams - Throughput 344
- Summary 345
- Traffic / Traffic Ethernet 348
- Summary (1588 PTP) 349
- NetBlazer 341 351
- Delay Measurement 352
- Total PTP Messages 352
- Summary (Cable Test) 353
- 346 FTB-700G/800 Series 356
- Summary (EtherSAM) 357
- Start Time 358
- NetBlazer 349 359
- Summary (FC BERT) 360
- Summary (ISDN PRI) 362
- NetBlazer 353 363
- Performance 365
- Statistics 366
- Summary (NI/CSU Emulation) 368
- Summary (RFC 2544) 369
- Latency Subtests 370
- NetBlazer 361 371
- Summary (S-OAM) 372
- NetBlazer 363 373
- Summary (SyncE) 376
- NetBlazer 367 377
- Summary (TCP Throughput) 378
- NetBlazer 369 379
- Ethernet Traffic 380
- Test Status 381
- Traces - OTN 383
- 374 FTB-700G/800 Series 384
- Traces - SONET/SDH 385
- Traffic - Ethernet 386
- Frame Size 387
- Traffic - Flow Control 388
- Pause Injection 389
- Traffic - Graph 390
- Traffic - S-OAM 391
- 382 FTB-700G/800 Series 392
- Traces/Label 393
- 10 Test Functions 395
- Test Functions 396
- NetBlazer 389 399
- FDL - Bit-Oriented Message 402
- 394 FTB-700G/800 Series 404
- Receive Messages 406
- Command/Response 407
- Generated Messages 408
- Received Messages 409
- Channel 413
- Channel Codeword 413
- Loopback Commands 415
- Filters 416
- Enabled Time 416
- Assign to Capture 417
- Filter Configuration 417
- 408 FTB-700G/800 Series 418
- Category Filter 418
- Filter Statistics 419
- Capture Source 420
- Frame Length 421
- Status and Controls 423
- Generate & Save 425
- OH - OTN 426
- NetBlazer 417 427
- NetBlazer 419 429
- OH - SONET/SDH 432
- Transport OH - Section/RS 433
- Transport OH - Line/MS 434
- NetBlazer 427 437
- STS/AU/TU-3 439
- NetBlazer 431 441
- NetBlazer 433 443
- 434 FTB-700G/800 Series 444
- Default all OH 445
- Ping & Trace Route 446
- NetBlazer 437 447
- Trace Route 448
- Status Description 449
- Pointer Adjustment 451
- 444 FTB-700G/800 Series 454
- Description 455
- 446 FTB-700G/800 Series 456
- 448 FTB-700G/800 Series 458
- RX Pointer Adjustment 462
- 454 FTB-700G/800 Series 464
- Measure Delay Button 465
- S-OAM Link Trace 467
- 458 FTB-700G/800 Series 468
- Signaling Bits 469
- Spare Bits 470
- NetBlazer 461 471
- 11 Test Control 473
- Discover Remote Button 474
- Local Module Identification 476
- Headset/DTMF Button 477
- 468 FTB-700G/800 Series 478
- Laser Button 479
- 470 FTB-700G/800 Series 480
- Loopback Tool tab 481
- NetBlazer 473 483
- Interface Tab 484
- NetBlazer 475 485
- Network tab 486
- SFP/SFP+ tab 486
- Phone Book Button 487
- Save/Load tab 488
- Import/Export tab 490
- Report Button 491
- Open Tab 493
- Import/Export Tab 494
- Reset Button 495
- Save/Load Button 496
- 488 FTB-700G/800 Series 498
- Start/Stop Button 502
- 12 Power Failure Recovery 503
- When Using the Test Timer 504
- 13 Suspend and Resume 505
- Resume Operation 506
- 14 Maintenance 507
- Cleaning LC Connectors 508
- Recalibrating the Unit 509
- Recycling and Disposal 510
- 15 Troubleshooting 511
- Transportation 512
- 16 Warranty 513
- Service and Repairs 515
- 506 FTB-700G/800 Series 516
- 17 Specifications 517
- Specifications 518
- Interfaces 519
- SFP Fibre Channel Interfaces 525
- SFP+ Fibre Channel Interfaces 526
- Synchronization Interface 527
- 18 Glossary 529
- 520 FTB-700G/800 Series 530
- Acronym List 530
- 522 FTB-700G/800 Series 532
- 524 FTB-700G/800 Series 534
- 526 FTB-700G/800 Series 536
- 528 FTB-700G/800 Series 538
- 530 FTB-700G/800 Series 540
- 532 FTB-700G/800 Series 542
- 534 FTB-700G/800 Series 544
- 10G Ethernet Client 545
- Glossary 546
- NetBlazer 539 549
- 1588 PTP Profiles 550
- 542 FTB-700G/800 Series 552
- Ethernet Cables 553
- Crossover Cable (1000 Mbit/s) 554
- 546 FTB-700G/800 Series 556
- NetBlazer 547 557
- NetBlazer 549 559
- 550 FTB-700G/800 Series 560
- Framing 560
- OTU FEC 560
- Overhead 561
- 552 FTB-700G/800 Series 562
- Optical Data Unit (ODU) 563
- 554 FTB-700G/800 Series 564
- Optical Payload Unit (OPU) 564
- NetBlazer 555 565
- Tandem Connection Monitoring 565
- 556 FTB-700G/800 Series 566
- NetBlazer 557 567
- Forward Error Correction 567
- ODU Multiplexing 568
- NetBlazer 559 569
- ODUflex 570
- MPLS Labels 571
- SONET/SDH 572
- Nomenclature 573
- 564 FTB-700G/800 Series 574
- Layer SONET SDH 574
- SONET Numbering Convention 576
- SDH Numbering Convention 577
- 4 respectively 579
- 570 FTB-700G/800 Series 580
- DSn/PDH Numbering Convention 581
- 572 FTB-700G/800 Series 582
- NetBlazer 573 583
- VLAN ID and Priority 585
- NetBlazer 577 587
- NetBlazer 579 589
- NetBlazer 581 591
- NetBlazer 583 593
- NetBlazer 585 595
- NetBlazer 587 597
- NetBlazer 589 599
- NetBlazer 591 601
- NetBlazer 593 603
- NetBlazer 595 605
- NetBlazer 597 607
- NetBlazer 599 609
- NetBlazer 601 611
- NetBlazer 603 613
- NetBlazer 605 615
- NetBlazer 607 617
- ₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩ 619
- MARKING REQUIREMENTS 620
Produits connexes et manuels pour Instruments de mesure Exfo FTB-800 Series for FTB-1
Instruments de mesure Exfo FTB-8100 Series Transport Blazer for FTB-200 Manuel d'utilisateur
(518 pages)
(518 pages)
Instruments de mesure Exfo FTB-8100 Series Transport Blazer for FTB-500 Manuel d'utilisateur
(719 pages)
(719 pages)
(574 pages)
Instruments de mesure Exfo FTB/IQS-85100G Packet Blazer for FTB-500/IQS-600 Manuel d'utilisateur
(448 pages)
(448 pages)
Instruments de mesure Exfo FTB/IQS-88000 Series Power Blazer for FTB-2/2Pro/5 Manuel d'utilisateur
(681 pages)
(681 pages)
Instruments de mesure Exfo FastReporter Data Post-Processing Software Manuel d'utilisateur
(256 pages)
(256 pages)
Instruments de mesure Exfo FastReporter Data Post-Processing Software Manuel d'utilisateur
(270 pages)
(270 pages)
(274 pages)
(47 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels